Discovery 2 Air Suspension Ride Height Sensor. Always support the vehicle on safety stands. Ensure the air suspension system is made safe before commencing work.
.jpg)
AIR SUSPENSION RIDE HEIGHT SENSOR FOR LAND ROVER DISCOVERY ebay.co.uk
Always support the vehicle on safety stands. Normally. a 2 sls spacer kit should also include extensions for the ride height sensors. Without modifying the ride height sensors. the sls system will just deflate the airsprings to negate the extra 2 lift youve installed.
jgs4x4.co.uk
Cheap pressure sensor. buy quality automobiles motorcycles directly from china suppliers:aroham rear air suspension ride height level leveling sensor for land rover discovery 2 td5 v8 rqh100030 enjoy free shipping. Suitable for the following land rover models:
.jpg)
ebay.com
Once you have lifted the rear by 50mm with spacers under the bags. ideally the suspension electronics need to be fooled into believing that it is standing level by adjusting the height sensors. Do not work on or under a vehicle supported only by a jack.
aliexpress.com
The normal ride height is when the car is horizontal. i know hawkeye asks you for calibration blocks but you can use two jacks under the body as to support it on even level(use a bubble level tool in the boot) then when hawkeye asks if you have calibration blocks fitted prompt yes and it will save those heights.if you want to be 100% accurate improvise some blocks. Ensure the air suspension system is made safe before.
.jpg)
ebay.co.uk
Rqh100030 suspension height sensor discovery 2 from john craddock ltd. Ensure the air suspension system is made safe before commencing work.
Source: aandaanimalhotel.co.uk
To lower to within 20 mm of the normal ride height as load is removed from the vehicle. Full of mud and water.
aliexpress.com
Disconnect the height sensor multiplug. Equivalent to land rover part number (s):
Fits Either Side. Left Or Right.
Position height sensor link to radius arm and tighten bolt to 25 nm (18 lbf.ft). The normal ride height is when the car is horizontal. i know hawkeye asks you for calibration blocks but you can use two jacks under the body as to support it on even level(use a bubble level tool in the boot) then when hawkeye asks if you have calibration blocks fitted prompt yes and it will save those heights.if you want to be 100% accurate improvise some blocks. Discovery 2 td5 v8 air suspension ride height sensor rear rqh100030 height sensor for all discovery 2/range rover l322 vehicles fitted with air suspension.
£ 28.95 Ex Vat ( £ 34.74 Incl Vat)
Disconnect the height sensor multiplug. Rqh100030g. oem suspension height sensor discovery 2 for discovery 2. land rover parts and range rover parts When the vehicle is stationary. a door is open and the ignition is off. the sls system will allow the rear of the vehicle.
Once You Have Lifted The Rear By 50Mm With Spacers Under The Bags. Ideally The Suspension Electronics Need To Be Fooled Into Believing That It Is Standing Level By Adjusting The Height Sensors.
The ride height sensors will detect the height of the chassis above the rear axle and sends that value to the ecu (part of the slabs ecu). The connectors terminals have corroded. Do not work on or under a vehicle supported only by a jack.
Position Height Sensor To Chassis And Tighten Bolts To 6 Nm (4.4 Lbf.ft).
Rear land rover discovery 2 l322 mark 3. Mechanically altering the height sensor position by extending the rods is probably the easiest and quickest way. Use testbook to calibrate height sensor.
Remove Stand(S) And Lower Vehicle.
Self levelling air suspension (sls) its common to find that the chassis harness connectors are. A replacement rear air suspension ride height sensor. Cheap pressure sensor. buy quality automobiles motorcycles directly from china suppliers:aroham rear air suspension ride height level leveling sensor for land rover discovery 2 td5 v8 rqh100030 enjoy free shipping.